Announcement

Collapse
No announcement yet.

Zero One Ads

Collapse

Show me your homemade spray jobs

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Show me your homemade spray jobs

    I wanna spray my M4. I'm just unsure what I want too go with,

    wanted to see a few of your spray jobs for ideas

    Thanks,

  • #2
    Re: Show me your homemade spray jobs

    Here is my blackhawk down attempt

    Best thing I find is to just get a few cans of krylon in some simular shades and go from light on the base to darkest.

    Did something simular on my g36. Get some wet and dry paper on there to rough it up aswell, makes it look less flat.

    Comment


    • #3
      Re: Show me your homemade spray jobs

      I'm liking that. Is it difficult to do?

      Comment


      • #4
        Re: Show me your homemade spray jobs

        Not too difficult to do, wouldn't say I'm much of an artist. Just take your time with it. I used krylon, khaki, light brown, dark brown and black. Do the whole gun in khaki first then do the stripes starting with lightest and building up to black.

        Comment


        • #5
          Re: Show me your homemade spray jobs


          Comment


          • #6
            Re: Show me your homemade spray jobs

            Comment


            • #7
              Re: Show me your homemade spray jobs

              I usually paint all my rifles, dont like the clean look. This was my first attempt at an AOR1 paint job.

              Comment


              • #8
                Re: Show me your homemade spray jobs

                Loving that mikey, what colours did you use and what did you use to get the pattern?

                Cheers

                Comment


                • #9
                  Re: Show me your homemade spray jobs

                  I used Krylon sand and Halfords camo brown. As for the pattern I just used some British scrim netting

                  Comment


                  • #10
                    Re: Show me your homemade spray jobs

                    That's awesome jester,

                    I wear multicam, but I think a multicam gun would be over the top.

                    What would you do? Go for a tan base and spray a slightly different colour in the pattern?

                    Comment


                    • #11
                      Re: Show me your homemade spray jobs



                      section 24 of the 1968 Act
                      Supplying imitation firearms to minors
                      1)It is an offence for a person under the age of eighteen to purchase an imitation firearm
                      2)It is an offence to sell an imitation firearm to a person under the age of eighteen.

                      Comment


                      • #12
                        Re: Show me your homemade spray jobs

                        When spraying. Is there anything I should be aware of?

                        Comment


                        • #13
                          Re: Show me your homemade spray jobs

                          This is my L119A1

                          Before painting...

                          pre_paint.jpg

                          Without much sun...

                          gun_full_dull.jpg

                          With lots of sun...

                          gun_full_sunny.jpg

                          Up close...

                          receiver_paint_detail.jpg

                          - - - Updated - - -

                          Originally posted by Dan88 View Post
                          When spraying. Is there anything I should be aware of?
                          Make sure all surfaces are clean and grease free. to do my camo job I did two coats of tan as the base colour, I think I did one coat and then as per the Krylon instructions I did another coat 15 minutes later. Then I waited until it was touch dry (like maybe 30 min) before applying other coats.

                          Comment


                          • #14
                            Re: Show me your homemade spray jobs

                            Looks decent.

                            Is it alright to spray the magazine?

                            Comment


                            • #15
                              Re: Show me your homemade spray jobs

                              Yeah I did. I put one in the mag well and drew along where it goes into the well and taped it up as you don't want to ware off loads of paint in the well. I taped up the mag well when painting the gun also.

                              Comment

                              About the Author

                              Collapse

                              Dan88 Find out more about Dan88
                              Working...
                              X