Upgrade guide Based on Maruzen type 96

[private parts]

Re: Upgrade guide Based on Maruzen type 96

As Guard has said, do the cheap upgrades first like barrel spacers etc, bbs going left might be too lighter ammo or mis aligned barrel

[purplebum100]

Re: Upgrade guide Based on Maruzen type 96

allso by bbs are going loads to the right

[purplebum100]

Re: Upgrade guide Based on Maruzen type 96

hey guys i have just boght a warrior l96 from here and i want to get it to 500 fps but i have read the first page and i dont have the money at the moment to get all of those upgrades so waht should i get first

[guard-sniper87]

Re: Upgrade guide Based on Maruzen type 96

Depends if you read the front page it will tell you

[Sabbath]

Re: Upgrade guide Based on Maruzen type 96

So what exactly do I need to buy to get it around 400fps?

[guard-sniper87]

Re: Upgrade guide Based on Maruzen type 96

The maruzen Will need stronge sears as they are only built to go at 380 from stock and will take max power of 430 without failing,

so get a set of polar sear type 96
will last along time and can go upto 650 fps without needking the zero trigger !

[badas]

Re: Upgrade guide Based on Maruzen type 96

To get a Maruzne l96 up to 400fps do i need to upgrade any sears at all?

Had mine at 480 and never had a problem after owning for 2 months, sold it on and the guy never got back in touch to tell me it broke and we kept in touch for some time.

[HunterAndy]

Re: Upgrade guide Based on Maruzen type 96

At some point you will, the original ones will probably wear out at some point but not as fast as upgrading to 500fps.

[Sabbath]

Re: Upgrade guide Based on Maruzen type 96

To get a Maruzne l96 up to 400fps do i need to upgrade any sears at all?

[guard-sniper87]

Re: Upgrade guide Based on Maruzen type 96

Just bought the Well AW338 springer. When I tried to fire it a pin fell out of the bolt handle.
I have put it back in but now I can't move the bolt at all.

Any suggestions please.

Regards Patrick.

you will have to take the cylinder out, and get into the the internals,

also if you can post the pic of the pin that fell out, this would help lots

[Patrick Hassett]

Re: Upgrade guide Based on Maruzen type 96

Just bought the Well AW338 springer. When I tried to fire it a pin fell out of the bolt handle.
I have put it back in but now I can't move the bolt at all.

Any suggestions please.

Regards Patrick.

[MilataryMupet]

Re: Upgrade guide Based on Maruzen type 96

yeah i was hoping you weren't going to say hop and barrel as that's the only place im not confident with accessing, in fact i haven't a clue how too
anyway thanks i will do some digging
thanks again

[guard-sniper87]

Re: Upgrade guide Based on Maruzen type 96

firstly, if you have a B&Q, go and get some silicone spray lubricant by 3in1, its in a yellow spray can, lasts for along time,

also the first place you want to start with upgrades is actual consistancy of the bb's

so barrel spacers, tb barrel, ptfe mods on both cylinder head and hop unit, using the correct weight ammo, and making the bolt pull smooth, and the big problem getting air seals spot on inside the actual cylinder and hop unit.....

I have repaired many rifles who said they have amazing air seals when infact they are worse then standard

[MilataryMupet]

Re: Upgrade guide Based on Maruzen type 96

hi guys
was just wondering were you would think the best place to start upgrading a warrior l96 would be, cylinder or barrel / hop ?
second thing now i know guard covered this in the main guide but i ordered what i thought was silicone spray as that what it was advertised as, and on reading the can it says for outside of guns only so what should i use and if its on zero one could someone please post the link
thanks
MM

[SSTSparkz]

Re: Upgrade guide Based on Maruzen type 96

Is there a picture basied tutorial on doing some maintance on these? I have a Warrior stock l96 that I have been using for the past 6 months and I havent done anything other than try to fix the empty mag indicator which still dont work and made some home made barrel spacers.

I want to try and upgrade as well as keep it in shape but I Would like to read a guide on what I'm doing and acually see what is needed to be done. 1 thing I think I need is a new hopup rubber where can I get these from which is best on a stock spring? or keeping it at 450fps