Toyko Marui Glock 17 and Serpa's

[Flubber 1123]

Now here is a question that I get varied answer to so I would like to set the record straight once and for all.

Can a Tokyo Marui Glock 17 custom (latest model) fit in a Glock 17 serpa holster? If there are any simple mods requried that an amateur can do to make the Glock fit could you please mention them as well.

Many thanks to everyone

[palmer234]

Re: Toyko Marui Glock 17 and Serpa's

Mine fits fine however you do have to trim the top of the serpa down a bit because of the thumb rest. Took 2 mins with a hacksaw and a smooth file to remove any sharp edges.

[Flubber 1123]

Re: Toyko Marui Glock 17 and Serpa's

Ok sounds promising the only thing is that I dont want to attempt to cut down the serpa then I cut to much and it either looks ugly/brake it. I might just take off the thumb rest though I have no idea how.

[plainlazy44]

Re: Toyko Marui Glock 17 and Serpa's

common consensus is that they generally don't fit in the serpa 17 as the tm slide is wider than real steel but apparantly they do fit well into the serpa for the glock 21.

I hate plastic holsters so i can't verify this as fact but its what i've read over and over again in many places.

[Mattman1991]

Re: Toyko Marui Glock 17 and Serpa's

how do you take off the thumb rest? ive always wanted to :D

[sniper34d]

Re: Toyko Marui Glock 17 and Serpa's

Buy a Glock 21 serpa and the TM G17 fits it perfect with no work required!

[riddick 1811]

Re: Toyko Marui Glock 17 and Serpa's

Buy a Glock 21 serpa and the TM G17 fits it perfect with no work required!

i've got this exact set up, and it works perfectly

[Metalbody]

Re: Toyko Marui Glock 17 and Serpa's

how do you take off the thumb rest? ive always wanted to :D

Tap out the retaining pin that goes through the frame and holds the rest in place. The rest should then just slide off.

Remember to put that pin back in though!!

[Apurturesci]

Re: Toyko Marui Glock 17 and Serpa's

Remember to put that pin back in though!!

Ouch, it sticks out like 5mm each side :p

[palmer234]

Re: Toyko Marui Glock 17 and Serpa's

I just measured mine with how much the gum rest needs to go down and used a junior hacksaw then filed the edges smooth. Fits perfectly.

[Metalbody]

Re: Toyko Marui Glock 17 and Serpa's

Ouch, it sticks out like 5mm each side :p

File it doughnut :D

[Flubber 1123]

Re: Toyko Marui Glock 17 and Serpa's

Ive tried tapping out the pin from both sides and it still dosen't want to budge!

[Boo-Sabum Ben]

Re: Toyko Marui Glock 17 and Serpa's

Use more force!

Just about to go down this route as Ive just ruined my safari land by heating it in the oven, in an attempt to stretch it out to get the block in with a light.

People have any trouble with the clone glock 21 holsters? Had some good things going with my old one for my hi capa

[caffin999]

Re: Toyko Marui Glock 17 and Serpa's

ben you put a safarliand in the oven!?!

[Boo-Sabum Ben]

Yup. It's what you do apparently to make the fit 100% except now it's just a weird shape and fits 0%, because when it cools down, it shrinks