Announcement

Collapse
No announcement yet.

Zero One Ads

Collapse

New Spring - Still bad FPS?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • New Spring - Still bad FPS?

    Well, got a classic army G36K here a few days ago.

    Chronoed at around 250fps using the stock spring.

    Upgraded by putting an Element M105 spring in (345fps). Now chronoes at 245fps...

    Any ideas?


    Please get in touch if you want general help. Please report problematic posts.

    Take responsibility for your choices. If you break any rule in life, you should be held accountable.

  • #2
    Re: New Spring - Still bad FPS?

    Air leak?
    Originally posted by Nun-Chuck
    I'm down every games day at EAG buddy just give me a shout and I'll whip it out, can have a squeeze too if you like.
    Originally posted by deanfirst
    why not use zeroone's escort service?

    Comment


    • #3
      Re: New Spring - Still bad FPS?

      Must be, but can't seem to think where exactly....


      Please get in touch if you want general help. Please report problematic posts.

      Take responsibility for your choices. If you break any rule in life, you should be held accountable.

      Comment


      • #4
        Re: New Spring - Still bad FPS?

        Yawn. Got a non CA V3 gearbox to hand? Check the respective lengths of the space where the spring sits. In V2 boxes the spring space is significantly longer.
        sigpic
        Tanaka M700 RealSword SVD TM VSR
        I want your broken Tanaka shotguns!

        Comment


        • #5
          Re: New Spring - Still bad FPS?

          I'd have expected more with a M105 though. My V2 CAs have run around the 320 fps mark with M100s
          Originally posted by Nun-Chuck
          I'm down every games day at EAG buddy just give me a shout and I'll whip it out, can have a squeeze too if you like.
          Originally posted by deanfirst
          why not use zeroone's escort service?

          Comment


          • #6
            Re: New Spring - Still bad FPS?

            The only other V.2 I have is in my M4A1, and she works fine... I can't imagine the difference in length should change much, not when it's less than an inch.

            Could it be any of these problems:

            Lube on gears is sticky rather than fluid
            Air Seal Nozzle not attached fully - pressed down into tappet plate enough
            Not enough lube overall
            Poor piston

            The spring is a real bitch to get in, holding a lot of tension, much more than the original one that was in there. Hate having to open the Gearbox(es) up when they are stiff springs. But will do so if necessary!


            Please get in touch if you want general help. Please report problematic posts.

            Take responsibility for your choices. If you break any rule in life, you should be held accountable.

            Comment


            • #7
              Re: New Spring - Still bad FPS?

              Sounds to me like youve got a rubbish air seal! try to get a new piston o-ring and then get the nozzle attached properly.
              Dboys KAC PDW - PEQ - Lipo - 2x midcaps - £150ono
              Classic Army B&T MP5A5 - Battery - 2x midcaps - £200ono
              2x Clone M9 GBB - 1 Mag Each - £50ea ono

              Comment


              • #8
                Re: New Spring - Still bad FPS?

                Okay thanks, I'll check it out!


                Please get in touch if you want general help. Please report problematic posts.

                Take responsibility for your choices. If you break any rule in life, you should be held accountable.

                Comment

                About the Author

                Collapse

                Gaffa Nicknamed "Gaffa" because I can be bossy, but get the job done! I'm built for comfort, not speed... Find out more about Gaffa
                Working...
                X