VSR10 HOP Replacement

[guard-sniper87]

Re: VSR10 HOP Replacement

As already stated by aribos

Read the massive thread on vsr upgrades and tips on the single action sub forum mate

Also the tm unit which is the newist version is best on market so no replacing needed

the big tech thread will give you all the info you need

[Fabzster]

Re: VSR10 HOP Replacement

Thanks again for all the assistance the information has been great! I appreciate it

I will go check the forum out

One last Question

How would u rate the EDGI upgrade package?

I emailed who I think is the guy for EDGI and he sent me the following:

BAR-10 UPGRADE



SPECS:

POWER/DURABILITY UPGRADE

1 Extension spring –SP01 -550FPS

1 Metal Piston -------------

ANODIZED Alloy with Stainless Steel base

Polyurethane Piston Seal and Teflon ring for extra smooth travel.



SPRING GUIDE

Stainless Steel

7mm OD

Highly polish, Perfect fit with the spring guide stopper

for smooth bolt push.

100mm length to provide maximum spring guide



TRIGGER PARTS

SEAR SET .

Piston and trigger Sear

Tool steel and tempered EDGI Style.



ACCURACY UPGRADE AND +20FPS

TIGHT BULL BARREL

HIGH SPEED Brass (Air Rifle Barrel)

435MM length

9.6MM Outside Diameter

6.01mm ID - Mirror finish

6.02Crater and Crowned

___________________________________

PRICE:

BAR10 UPGRADE Kit



Sp01 Spring and Metal Piston (550 – 585FPS) -$65

Spring Guide $25

Trigger/piston Sear $40

Tight Bull Barrel (435,6.01) -$70

Spring Guide Stopper -$15

FEDEX Shipping () -$60



TOTAL ----------------------------------$275

Anyone have esxperience with these parts?

[aribos]

Re: VSR10 HOP Replacement

He makes awesome parts just remember with springs etc it might tip you over the fps as he works with the rules of up to 700 fps not 500.

[Fabzster]

Re: VSR10 HOP Replacement

K so I could just get the upgrade package I posted above and I should be good?
Just need to watch out for the spring, I have replied to his email and asked for a spring to keep me at 500

I noticed that the package does not contain a cylinder head

Is there anything else that i would need if i get that package

[aribos]

Re: VSR10 HOP Replacement

Standard cylinder head will probably be fine to be fair, the dampner one is just to keep it silent so they apply more to the g-spec

[guard-sniper87]

Re: VSR10 HOP Replacement

Standard version cylinder head is fine mate

Just polish it with brasso and will be perfect

[Fabzster]

Re: VSR10 HOP Replacement

thanks for the great feedback, I was searching via google for other posts on VSR's and I found this one, great stuff! hope it helps some peeps.

I ended up ordering the full EDGI package.

Now the Jaru Bane springs were mentioned earlier can one put them with the upgrades I purchased in the VSR10 trigger mech? Would these make my trigger much lighter?

I will have to drill the pin out of my cylinder, I managed to find a 1/8 or 3mm Bit to do the job. I have seen various tutorials on this anyone have experience on this and advice?

And lastly with regards to BB's what do you reccomend?

[aribos]

Re: VSR10 HOP Replacement

Use a pillar drill for the cylinder, you need to have it held in a vice etc and keep it at a slow drilling speed.

BB wise, you'll want heavyweight so .30g upwards. Madbull, SGM's, Devils. There are a whole range out there. With most people its a see what weight you get on with most and also which ones are most cost effective to your budget for games (A cheaper pack of i.e. 1000 .30 ASG Blaster BB's are around 7 quid but you can pay anywhere up to 20 quid for a pack of a couple of thousand of the best quality)

[Fabzster]

Re: VSR10 HOP Replacement

flip I only have a hand held one, do think if i make a pilot hole I could do it without a vice and Pillar drill?

I have KSC 0.30 and I can get the Madbull 0.43's (What do you think of the Madbulls)

Also do you think I will need a teflon Cylinder with the EDGI Kit that I ordered? what would work well with it?

[aribos]

Re: VSR10 HOP Replacement

Yea madbulls are good, so are the KSC from what I hear (I just use cheap and cheerful at the moment due to joblessness)

You will need a vice either way. If you cant best thing to do is ask your local shop etc if they have someone who can do it for you or if you have a sniper at your site who does a lot of guns (there are like 5 or 6 of us at MCG) then ask one of them as they will of done it many times and even if they charge a small nominal fee at least you know its done and done properly.

[Fabzster]

Re: VSR10 HOP Replacement

great I will get a bottle of those and try them out.

I will have to ask my cousin, I live in South Africa

K Kewl will make a plan shot for the info

[Fabzster]

Re: VSR10 HOP Replacement

If I would like to get a teflon cylinder to bypass the removal of the pin could I get the laylax teflon cylinder?
http://www.redwolfairsoft.com/******...l?prodID=17927

Would this work well with the EDGI Parts?